MA2 CONSULTANTS

CBR results requested / Refer to site specific construction table to ascertain approved specification.

INSERT

Formation cut undertaken during wet conditions.

INSERT

Condition of formation saturated reduce cut, cap, and protect appropriately.

INSERT

Provision of Geotextile membrane recommended.

INSERT

Provision of Geotextile membrane instructed.

INSERT

Formation not cut or trimmed to tolerance specified +10 or -30mm.

INSERT

Identified soft spots (Excavate and backfill with similar surrounding material).

INSERT

Formation not compacted at time of inspection.

INSERT

Formation not compacted sufficiently prior to placement of granular construction material.

INSERT

Inappropriate compaction plant equipment in use.

INSERT

Root infestation requires excavation to remove.

INSERT

Vehicular trafficking identified (Formation should not be trafficked) reduce cut, cap, and protect appropriately.

INSERT

Extensive sub formation failure identified (Evaluate and agree remedial procedure with LA site engineer).

INSERT

Formation frozen (Compaction not to be undertaken in such conditions).

INSERT

Transport vehicles trafficking over formation (Formation should not be trafficked) reduce cut, cap, and protect appropriately.

INSERT

Placement of fill material in excessively deep construction layers, Evaluation of compaction plant capability required to ascertain compaction rate and placement depth of layers.

INSERT

Testing in compliance of imported fill material inclusive moisture content requested.

INSERT

Placement of quarried 6F5 material works in progress (Refer to site specific construction table to ascertain thickness of construction dependent upon CBR values achieved).

INSERT

Placement of recycled 6F2 material works in progress (Refer to site specific construction table to ascertain thickness of construction dependent upon CBR values achieved).

INSERT

CBR compaction test results requested, to achieve a minimum 15% CBR value via a 450mm diameter test plate .

INSERT

Recycled 6F2 material requires grading certification 1 per each 100tonne produced.

INSERT

Capping layer construction depth exceeds maximum 225mm specified.

INSERT

Capping layer depth constructed less than minimum 110mm specified.

INSERT

Granular material frozen (Must be free from ice to achieve maximum compaction values).

INSERT

Inconsistent construction levels (Tolerance +10 or -30mm specified) Cut and trim to tolerance accordingly.

INSERT

Capping material not compacted during time of inspection.

INSERT

Capping material not compacted sufficiently prior to placement of Type 1 GSB.

INSERT

Inappropriate compaction plant equipment in use.

INSERT

Soft spots identified within capping layers.

INSERT

Wheel rutting identified within capping layers.

INSERT

Material contamination in excess of maximum 1% approved.

INSERT

Provision of conveyance ticket requested.

INSERT

Placement of quarried material works in progress (Refer to site specific construction table to ascertain thickness of construction dependent upon CBR values achieved).

INSERT

Placement of recycled material works in progress (Refer to site specific construction table to ascertain thickness of construction dependent upon CBR values achieved).

INSERT

CBR compaction test results requested, to achieve a minimum 30% CBR value via a 300mm diameter test plate.

INSERT

Recycled material requires grading certification 1 per each 100tonne produced.

INSERT

Type 1 GSB layer construction depth exceeds maximum 225mm specified.

INSERT

Capping layer depth constructed less than minimum 110mm specified.

INSERT

Type 1 GSB material frozen in situ (Must be free from ice to achieve maximum compaction values).

INSERT

Inconsistent construction levels (Tolerance +10 or -30mm specified) Cut and trim to tolerance accordingly.

INSERT

Type 1 GSB material not compacted during time of inspection.

INSERT

Type 1 GSB material not compacted sufficiently prior to placement of bituminous materials.

INSERT

Inappropriate compaction plant equipment in use.

INSERT

Soft spots identified within Type 1 GSB material (Excavate and reconstruct accordingly).

INSERT

Wheel rutting identified within Type 1 GSB material (Excavate, construct, and reconsolidate accordingly).

INSERT

Material contamination in excess of maximum 1% approved.

INSERT

Provision of conveyance tickets requested.

INSERT

As dug / site won material used for trench backfill (Unacceptable without prior agreement with WCC engineer).

INSERT

Excessive backfill layer depths identified. Maximum 225mm approved as standard with routine compaction evaluations undertaken throughout.

INSERT

Irregular constructed levels identified throughout trench backfill. Maximum 225mm approved as standard (Consistent trimmed layers required).

INSERT

Placement of recycled trench backfill material WIP.

INSERT

Placement of quarried trench backfill material WIP.

INSERT

Placement of approved site won trench backfill material WIP.

INSERT

No compaction of trench back fill evident.

INSERT

Frequency of compaction insufficient between layers.

INSERT

Granular material frozen (Must be free from ice prior to placement).

INSERT

Material contamination excessive.

INSERT

Provision of conveyance ticket requested.

INSERT

Compaction test results requested / TBC.

INSERT

Visual inspection of material is excessively wet (Moisture content tests requested).

INSERT

Sides of trench destabilised, backfill with similar surrounding material.

INSERT

Pipes diameter is not in accordance with specification.

INSERT

Manufactured pipe material TBC in compliance with specification.

INSERT

Pipe/s broken or cracked in-situ.

INSERT

Inconsistent pipe alignment and or level.

INSERT

Pipe bedding and surround material not provided.

INSERT

Pipe bedding material compliance with specification TBC with provision of conveyance ticket or testing as requested.

INSERT

Pipe bedding material contaminated.

INSERT

Insufficient depth of minimum 1.2m over pipe, requires concrete bed and surround protection.

INSERT

Rocker pipe not installed at inspection chamber.

INSERT

Expansion joint fibre board not installed as specified.

INSERT

Connection unsatisfactorily completed.

INSERT

Manufactured in line pipe connections required.

INSERT

Optional plastic gully pots approved to specified concrete.

INSERT

Location of road gully not in accordance with proposed layout.

INSERT

Proposed gully installation not located due to ramping materials.

INSERT

Proposed gully installation not located in proposed position.

INSERT

Lateral pipe connection adjoined and not singular to main or inspection chamber as specified.

INSERT

Proposed double gullies installed as singles.

INSERT

Gully pot positioned to far forward of constructed kerb foundation.

INSERT

Gully pot position situated to far back underside of constructed kerb foundation.

INSERT

Allowance for minimum of two or maximum of three courses of engineering bricks TBC.

INSERT

Insufficient concrete surrounding gully pot.

INSERT

Excessive amount of concrete surrounding gully pot.

INSERT

Mortar blown between brick courses off top of pot.

INSERT

Brickwork blown underside of ironworks apparatus.

INSERT

Specified mortar resin to affix ironworks unconfirmed.

INSERT

Gullies ironworks level low situated within section of carriageway.

INSERT

Gullies ironworks level high situated within section of carriageway.

INSERT

Gullies ironworks damaged situated within section of carriageway.

INSERT

Irregular gullies ironworks level situated within section of carriageway.

INSERT

Gullies ironworks not in accordance with specification.

INSERT

Settlement visually evident surrounding gullies ironworks.

INSERT

Gullies ironworks installed wrong way around.

INSERT

Gullies ironworks position situated incorrectly atop pot.

INSERT

Gullies ironworks position situated forward of kerb face.

INSERT

Gullies ironworks unsupported to front of pot.

INSERT

Gullies ironworks unsupported to back of pot.

INSERT

Gullies ironworks unsupported to sides of pot.

INSERT

Gullies cover rattling inside of frame.

INSERT

Gullies frame and cover loose and rocking in situ.

INSERT

Gullies hinge broken, requires replacement.

INSERT

Pedestrian grating required in location.

INSERT

Pedestrian grating installed incorrectly.

INSERT

Gullies ironworks clanking in situ when traversed by vehicles.

INSERT

Each individual gully requires separate lateral connection to main or associated inspection chamber.

INSERT

Lateral pipe diameter installation is not in accordance with specification.

INSERT

Lateral pipe manufacturers material is not in accordance with specification.

INSERT

Concrete bed and surround not provided over full length of lateral pipe.

INSERT

Concrete bed and surround not provided.

INSERT

Concrete bed and surround only provided down to 1.2m and not as specified.

INSERT

Inconsistent line and level.

INSERT

Diameter of ring TBC in accordance with specification.

INSERT

Excessive cuts in rings identified to incorporate drainage inlets and outlet pipes.

INSERT

Rings cut to incorporate drainage pipes are unapproved and require replacement.

INSERT

Ring cut down to accord with cover slab, structural integrity to be assessed.

INSERT

Ring cracked or fractured in situ.

INSERT

Sealant between rings not evident.

INSERT

Sealant between rings protruding into chamber.

INSERT

Open joints surrounding pipe inlet/outlet.

INSERT

Benching outstanding.

INSERT

Benching blown and or damaged.

INSERT

Snots over benching.

INSERT

Mortar blown to brickwork / risers or underside of frame and cover.

INSERT

Excessive mortar joints in excess of 10mm.

INSERT

Lifting eyes require filling.

INSERT

Water infiltration evident down the side of rings or over benching. Preventative measures required accordingly.

INSERT

Water infiltration evident around pipe connections into inspection chamber. Preventative measures required accordingly.

INSERT

Specified mortar resin to affix ironworks unconfirmed.

INSERT

Constructed cover slab level mirroring through carriageway bituminous construction.

INSERT

Review required to ascertain requirement for steps or ladder installation.

INSERT

Installation of steps or ladder outstanding.

INSERT

Steps installed do not accord with specification (Steps x 300mm wide at 250mm centres in encapsulated plastic).

INSERT

Ladder installed does not accord with specification (Steel ladders installed no greater than 675mm from top of cover and frame).

INSERT

Steps installed are damaged and require replacement.

INSERT

Steps installed are not secured to structure of rings and require replacement.

INSERT

Steps do not alight onto benching landing.

INSERT

Aperture of ironworks does not align with location of installed steps.

INSERT

Ladder installed is damaged and requires replacement.

INSERT

Ladder installed is not secured to structure of ring and requires replacement.

INSERT

Ladder does not alight onto benching landing.

INSERT

Aperture of ironworks does not align with location of installed ladder.

INSERT

Safety chains installation where the outgoing pipe diameter is 600mm or greater outstanding, broken our not secured satisfactorily.

INSERT

Settlement visually evident surrounding inspection chamber, potentially as a consequence of a lack of compaction.

INSERT

Inspection chambers ironwork’s level low situated within section of carriageway.

INSERT

Inspection chambers ironwork’s level high situated within section of carriageway.

INSERT

Inspection chambers ironwork’s damaged situated within section of carriageway.

INSERT

Irregular inspection chamber level situated within section of carriageway.

INSERT

Inspection chambers ironwork’s specification not in accordance with specification.

INSERT

Inspection chamber ironworks loose and rocking in situ.

INSERT

Ironworks clanking in situ when traversed by vehicles.

INSERT

HFS (High Friction Surface) inspection chamber cover not provided as specified.

INSERT

Settlement visually evident surrounding ironworks.

INSERT

Delivery and laying temperature issues (Refer to guidelines / specifications).

INSERT

Post placement of Matrix in excess of 10 days.

INSERT

In unsuitable conditions or emergencies post 10 days placement refer to laying specifications.

INSERT

Laying tolerances in excess of specified maximum of +or- 15mm.

INSERT

Laying of surfacing material undertaken in temperatures below -1 on rising thermometer.

INSERT

Standing surface water evident prior to commencement of laying material.

INSERT

Prolonged rain during laying process of material noted and advised to operatives and available site management.

INSERT

Excessively windy conditions (Refer to laying temperature specifications).

INSERT

Falling debris etc i.e. tree / hedge arisings compacted within matrix layer.

INSERT

Compaction issues noted and to be reviewed as advised to operatives and available site management.

INSERT

Excessively open texture course identified in section of carriageway.

INSERT

Aggregate egress evident in section of carriageway.

INSERT

Laying process undertaken on wet/saturated granular material, as advised to operatives and available site management.

INSERT

Granular construction rutting under weight of plant, equipment, and delivery lorries.

INSERT

Nuclear density measurements not being undertaken at time of placement of material.

INSERT

Delivery and laying temperature issues (Refer to guidelines / specifications).

INSERT

Post placement of Matrix in excess of 10 days.

INSERT

In unsuitable conditions or emergencies post 10 days placement refer to laying specifications.

INSERT

Application of Bond coat omitted between AC32 and AC20.

INSERT

Application of Bond coat insufficient rate of spread between AC32 and AC20.

INSERT

Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

Placement undertaken below -1 Air temperature on rising thermometer.

INSERT

Standing surface water evident prior to commencement of laying material.

INSERT

Prolonged rain during laying process of material.

INSERT

Excessively windy conditions (Refer to laying temperature specifications).

INSERT

Compaction issues! noted and to be reviewed as advised to operatives and available site management.

INSERT

Excessively open texture course identified in section of carriageway.

INSERT

Aggregate egress evident in section of carriageway.

INSERT

Laying process undertaken on wet/saturated granular material.

INSERT

Base course construction rutting under weight of plant and equipment.

INSERT

Nuclear density measurements not being undertaken at time of placement of material.

INSERT

Falling debris etc i.e., tree / hedge arisings compacted within matrix layer.

INSERT

Debonding visually evident in section/s.

INSERT

Delivery and laying temperature issues (Refer to guidelines / specifications).

INSERT

Application of Bond coat omitted between AC20 and Surface course material.

INSERT

Application of Bond coat insufficient rate of spread between AC20 and Surface course material.

INSERT

Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

Placement undertaken below -1 Air temperature on rising thermometer.

INSERT

Standing surface water evident prior to commencement of laying material.

INSERT

Prolonged rain during laying process of material.

INSERT

Excessively windy conditions (Refer to laying temperature specifications).

INSERT

Compaction issues! noted and to be reviewed as advised to operatives and available site management.

INSERT

Excessively open texture course identified in section of carriageway.

INSERT

Aggregate egress evident in section of carriageway.

INSERT

Base and Binder course construction rutting under weight of plant and equipment.

INSERT

Falling debris etc i.e., tree / hedge arisings compacted within matrix layer.

INSERT

Debonding visually evident in section/s.

INSERT

Open joint evident to face of kerb.

INSERT

Open surfacing joint requires over banding (Hapas approved material specified).

INSERT

Finished levels above specified 125mm kerb face (Note +or – 5mm tolerance).

INSERT

Finished levels below specified 125mm kerb face (Note +or – 5mm tolerance).

INSERT

Kerb foundation dimensions non-compliance with specification.

INSERT

Concrete specification non-compliance (ST4 specified).

INSERT

Slump of concrete to dry.

INSERT

Slump of concrete too wet.

INSERT

No poker vibrator in use on site at time of placement of foundation concrete.

INSERT

No poker vibrator in use on site at time of placement of backing concrete.

INSERT

Backing concrete constructed to high (Specified 85mm below top of kerb).

INSERT

Backing concrete constructed to low (Specified 85mm below top of kerb).

INSERT

Kerb mortar bedding material to dry.

INSERT

Kerb mortar bedding material to wet.

INSERT

Kerb spacing between kerbs excessive (2mm specified).

INSERT

Kerb spacing between kerbs to tight (2mm specified).

INSERT

150 x 125 BN kerb installation not in compliance with specified 225 x 125mm kerb in section.

INSERT

Width of constructed BN kerbs insufficient to negotiate access onto private driveway.

INSERT

Extend BN kerb width to accord with associated vehicular crossing with allowance for entry and exit over extent of BN kerb.

INSERT

Excessive width of BN kerbs in section.

INSERT

Reduce width of BN kerbs in section.

INSERT

Adjoining DR1 / DL1 kerbs in section unacceptable.

INSERT

Kerb face in section is in excess of specified 125mm.

INSERT

Kerb face in section installed below specified 125mm.

INSERT

BN kerb upstand in excess of specified maximum of 6mm over Pedestrianised crossing location.

INSERT

BN kerb upstand below specified 3-6mm specification.

INSERT

Detritus / standing surface water evident over BN kerb in section.

INSERT

Kerb alignment not in accordance with design / layout.

INSERT

Radii kerbs non-compliance with design / layout.

INSERT

Radii kerbs high in situ between tangents.

INSERT

Radii kerbs low in situ between tangents.

INSERT

Numerous kerbs throughout the development have sustained damage, are loose, cracked and rocking. Kerb replacement in agreement with LA site engineer.

INSERT

Numerous kerbs throughout the development have sustained minor damage, a successfully applied, colour matched epoxy resin kerb repair acceptable.

INSERT

Numerous kerbs in section are displaced forward out of alignment.

INSERT

Numerous kerbs in section are displaced back out of alignment.

INSERT

Kerbs in section have become divorced of in situ backing concrete.

INSERT

Open joint evident to face of kerb.

INSERT

Internal angles not provided in location.

INSERT

Specified 200mm Flat Top edging kerbs not installed over vehicular access.

INSERT

Bullnose edging kerbs installed through soft margin / visibility splays and not Flat Top edging kerbs as specified.

INSERT

Flat edging kerbs installed to back of footway and not Bullnose edging kerbs as specified.

INSERT

Insufficient compaction to utilities trenches back fill within section of footway.

INSERT

Unacceptable utilities trench backfill material within section of footway.

INSERT

Unacceptable placement of utilities backfill material within section of footway.

INSERT

Formation not cut to level and tolerance within section of footway.

INSERT

Formation not compacted within section of footway.

INSERT

Insufficient depth of Type 1 GSB constructed within section of footway (150mm specified).

INSERT

Insufficient depth of Type 1 GSB constructed within vehicular access (2000mm specified).

INSERT

Insufficient compaction of Type 1 GSB within section of footway.

INSERT

Insufficient compaction of Type 1 GSB within vehicular access.

INSERT

Delivery and laying temperature issues (Refer to guidelines / specifications).

INSERT

AC32 Basecourse exceeds height of kerb backing concrete (85mm below top of kerb required).

INSERT

AC32 Laying tolerances in excess of specified maximum of +or- 15mm.

INSERT

Application of Bond coat omitted between AC32 and AC20.

INSERT

Application of Bond coat insufficient rate of spread between AC32 and AC20.

INSERT

Lack of compaction over AC32 material in section of footway.

INSERT

Excessively open texture course identified in AC32 within section of footway.

INSERT

Numerous AC32 level irregularities throughout section of footway.

INSERT

Settlement evident in AC32 within section of footway.

INSERT

AC20 Binder course levels too high to allow for application of 25mm AC6 surface course material.

INSERT

AC20 Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

Application of Bond coat omitted between AC32 and AC20.

INSERT

Application of Bond coat insufficient rate of spread between AC32 and AC20.

INSERT

Lack of compaction over AC20 material in section of footway.

INSERT

Excessively open texture course identified in AC20 within section of footway.

INSERT

Numerous AC20 level irregularities through section of footway.

INSERT

Settlement evident in AC20 within section of footway.

INSERT

Application of Bond coat omitted between AC20 and AC6.

INSERT

Application of Bond coat insufficient rate of spread between AC20 and AC6.

INSERT

Numerous AC6 surface course level irregularities within section of footway.

INSERT

Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

AC6 surface course level low off back of kerbs in section of footway.

INSERT

AC6 surface course level high to back of kerbs in section of footway.

INSERT

Settlement evident in AC6 surfacing within section of footway.

INSERT

Standing surface water evident within section of footway.

INSERT

Longitudinal cracks evident within section of footway.

INSERT

Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

Aggregate egress evident within section of footway.

INSERT

Aggregate egress evident within vehicular crossing.

INSERT

Insufficient gradient / crossfall constructed over footway (1:40 specified).

INSERT

Excessive gradient / crossfall constructed over footway (1:40 specified).

INSERT

Insufficient gradient / crossfall constructed over vehicular crossing (1:12 specified).

INSERT

Excessive gradient / crossfall constructed over footway (1:12 specified).

INSERT

Vehicles grounding over back of vehicular access onto private driveway.

INSERT

Laying tolerances in excess of specified maximum of +or- 6mm.

INSERT

Placement of bituminous material undertaken below -1 Air temperature on rising thermometer.

INSERT

Standing surface water evident prior to commencement of laying material.

INSERT

Prolonged rain during laying process of material.

INSERT

Excessively windy conditions (Refer to laying temperature specifications).

INSERT

Compaction issues! noted and to be reviewed as advised to operatives and available site management.

INSERT

Excessively open texture course identified in section of footway.

INSERT

Aggregate egress evident in section of footway.

INSERT

Base and Binder course construction, wheel rutting under weight of parked vehicles.

INSERT

Falling debris etc i.e., tree / hedge arisings compacted within matrix layer.

INSERT

Debonding visually evident in section/s.

INSERT

Tactile paving slabs cracked in situ.

INSERT

Nodules damaged on Tactile paving slabs.

INSERT

Tactile paving slabs loose and rocking in situ.

INSERT

Tactile paving misaligned to opposite side of carriageway.

INSERT

Tactile paving misaligned to central pedestrian refuge.

INSERT

BN kerb up stand exceeds specified 6mm.

INSERT

Standing surface water evident over top of BN kerb.

INSERT

Detritus evident over top of BN kerbs.

INSERT

Gully missing up stream of Tactile paved crossing point.

INSERT

Gully located within / over Tactile paving crossing point.

INSERT

Tactile paving slabs low in situ.

INSERT

Tactile paving slabs high in situ.

INSERT

Verge margin levels low, make up to level with approved topsoil inclusive application of grass seed or turf as appropriate.

INSERT

Verge margin rutted as a consequence of vehicles overrunning.

INSERT

Verge margins rutted throughout the development as a consequence of vehicles overrunning. Installation of grass-crete to be considered.

INSERT

Application of grass seed required / outstanding to verge margins.

INSERT

Provision of Turf required in verge margins.

INSERT

Stop taps level low within section of verge margin.

INSERT

Stop taps level high within section of verge margin.

INSERT

Access slabs constructed over verge margin are not approved or acceptable, bituminous construction specified.

INSERT

Boulders situated within verge margin are to be removed.

INSERT

Planters situated within verge margin are to be removed.

INSERT

Provision of New Rd Layout signs outstanding.

INSERT

Removal of New Rd Layout signs required.

INSERT

Post cap/s missing, provide and fix.

INSERT

Signpost loose in footing, construct foundation to specification.

INSERT

Sign face damaged, requires replacement.

INSERT

Sign turned wrong way around post, affix sign securely to post.

INSERT

Signpost clips missing, provide and fix.

INSERT

Sign rail fixing to post damaged, replace rail and sign accordingly.

INSERT

Insufficient mounting height (Refer to sign specification table) adjust accordingly.

INSERT

Sign mounting height to high (Refer to sign specification table) adjust accordingly.

INSERT

Number of posts installed not in compliance with specification (Refer to sign specification table).

INSERT

Diameter of post/s installed not in compliance with specification (Refer to sign specification table).

INSERT

Proposed sign installation remains outstanding.

INSERT

Keep left bollard loose in base.

INSERT

Kee left bollard base loose.

INSERT

Keep left bollard base bolts missing.

INSERT

Keep left bollard damaged.

INSERT

Keep left bollards require cleansing.

INSERT

Road markings worn throughout the development / scheme and requires retracing.

INSERT

Road markings outstanding (Refer to approved signing and lining drawing).

INSERT

Give way Road markings outstanding (Refer to approved signing and lining drawing).

INSERT

Give Way Triangle outstanding.

INSERT

Speed restriction Terminal / Roundel installation outstanding.

INSERT

Speed restriction Terminal / Roundel installation worn and requires retracing.

INSERT

Road markings incorrectly lead into kerb face of pedestrian refuge, remove, and retrace to amend direction of line is forward 150mm of kerb face.

INSERT

Configuration of road markings not installed as proposed / approved.

INSERT

Installation of single / double yellow line/s outstanding.

INSERT

Installation of single / double yellow line/s unapproved.

INSERT

Removal of road markings undertaken by Hydro blasting procedures.

INSERT

Damage sustained to the carriageway as a consequence of removal will require reinstatement in agreement with LA site engineer.

INSERT

Welcome to
FILES

Got a question? Get in touch.

Welcome to FILES

Got a question? Get in touch.

Welcome to
FILES